Manufacturer Part# / Cross Reference Search
Please use this search function to find READY die set components that are equivalent to commonly used pins, bushing, ISO Springs, and Gas Springs from other manufacturers.
Please Note: We believe this cross reference to be accurate. Please review the specifications to ensure the item will work in your application. Gas Spring equivalents were based on body dimensions, on contact force and stroke length.
Ready recommends using only a premium grade of hydraulic oil.
The H-1 pump is available in six standard sizes. Each pump has four ports to activate up to four identical H-2 units. The quantity, size, and stroke length of the H-2 units hosed to each pump determines the size and oil volume of the pump needed. Pumps can be up to six feet away from H-2 units. This allows you to free up critical die space and balance die loads.
The H-1 pump is available in six standard sizes. Each pump has four ports to activate up to four identical H-2 units. The quantity, size, and stroke length of the H-2 units hosed to each pump determines the size and oil volume of the pump needed. Pumps can be up to six feet away from H-2 units. This allows you to free up critical die space and balance die loads.
Unit of Measure
Specifications
Brands |
N/A HYDROCAM® Ready |
Total Volume (VT) |
N/A 50 cm³3.051 in³ |
Total Volume (Volume/Stroke Per mm) |
N/A 2.235 cm³3.4636 in³ |
Die Open Height (Ht 1) |
N/A 133 mm5.236 in |
Height of Base (Ht 2) |
N/A 41 mm1.614 in |
Maximum Volume Stroke (Ht 4) |
N/A 23 mm0.906 in |
Approach Stroke (Ht 5) |
N/A 8 mm0.315 in |
Piston Diameter (D1) |
N/A 53.34 mm2.100 in |
Rod Diameter (D2) |
N/A 20 mm0.787 in |
Body Diameter (D3) |
N/A 82 mm3.228 in |
Minimum Diameter (D4) (Not Supplied) |
N/A 45 mm1.772 in |
Minimum Base Cross Corners Diameter (D5) |
N/A 120 mm4.724 in |
Minimum Optional Gauge Diameter (D6) |
N/A 80 mm3.150 in |
Base Square 1 |
N/A 90 mm3.543 in |
Bolt Hole Pattern Square 2 |
N/A 72 mm2.835 in |
Piston Area (P) |
N/A 22.35 cm²3.464 in² |
Piston Rod Travel |
N/A Piston rod travel controls oil volume going to the H-2 unit(s). |
Optional Stroke Gauge Ring |
N/A Used as a visual gauge to assist in set-up. Ring is located on top of pump body and made to the appropriate height based upon piston rod travel calculation. This stroke gauge ring is not a stop block and should be used for set-up purposes only. |
Total Stroke (Ht3) |
N/A 31 mm1.220 in |
Product Code |
N/A HC |
Dimensions
Dimension (M) (x4) |
N/A M8 |
Dimension (G) (x4) British Standard Pipe Parallel Thread (BSPP) Size |
N/A G-3/8 |
Mounting Suggestions
Mounting Suggestions |
N/A
|
Options
Options |
N/A
Oil Return Option The oil return option can be an alternative to nitrogen, as a method of returning or retracting the H-2 unit. This option requires a hose from the H-2 unit to an external nitrogen/oil accumulator. The typical operating pressure of the forced oil return option is 100 bar (1450 psi). This option may require careful engineering analysis in order to calculate what is best for a customer’s application. READY can assist in this evaluation. User Sequence Option This option requires careful application engineering to determine feasibility. Engineering fees may apply. User sequence can allow customers to control the timing of their HYDROCAM® Systems. The H-2 unit can be programmed to extend, dwell, and retract at nearly any point in the stroke. This allows for multiple actions to be performed in a single operation. Contact Ready for the latest developments on this exciting HYDROCAM® system technology. Direct Punch Option This option is used when piercing round holes only. A metric punch of the proper size range can be used. The punch shank size is limited, and is listed on the bottom of the H-2 selection chart. By removing the standard front plate, the H-2 piston will accept a customer supplied head type punch. A special locking nut is included with this option. The direct punch option fits compact areas. |